Custom Outdoor Aluminium Staircase
Designed and fabricated in-house: 20 mm aluminium stringers with RHS aluminium steps, rust-resistant and built to last, with integrated lighting. Stone tiles and glass balustrades follow from other trades.
Handy Tradie 4 U does welding and metal fabrication across the Illawarra and South Coast, from Helensburgh down to Nowra. Most work gets done on site at your place. Jobs that need a bench, a clamp and some room get built in the workshop and fitted when they are ready.
We work for homeowners whose gate has stopped closing, builders who need steel cages before a pour, and businesses with a machine sitting idle in the yard. The work is licensed and insured. Send a photo or call 0413 147 335 and you will get a straight answer on what the job needs and how it gets quoted.
Four kinds of work make up most of what comes through the door, and most of it is repair or one-off rather than off-the-shelf.
Steel and aluminium gates built to the opening you have, which is rarely the size a kit gate comes in. We reframe gates that have dropped and stopped latching, replace snapped hinges and worn latches, and weld in new posts where the old ones have rusted off at ground level. New driveway gates, side gates and pool gates get built from scratch. There is more detail on gates, handrails and balustrades.
Stair rails, balcony balustrades, pool fencing and wall-mounted grab rails in mild steel, stainless or aluminium. The rules matter on this work. A barrier is required where the fall is 1 metre or more. Minimum barrier height is 865mm measured above the nosing line of stairs and above ramps, and 1m above landings, balconies and other floors. No opening may let a 125mm sphere pass through, and where the opening sits at the edge of the floor the gap is 40mm. Where the fall exceeds 4m a no-climb rule also applies, with no horizontal or near-horizontal elements between 150mm and 760mm above the floor. Barrier loads are designed to AS/NZS 1170.1 and wind to AS 1170.2.
The opening detail is where most patch-up repairs come undone, because a rail can be re-welded and still pass a 125mm sphere. One other thing worth knowing: AS 1428.1 does not govern domestic stair handrails, so it is not the right reference for a house.
Lintels, posts, brackets, bearers and steel reinforcement cages for concrete footings. If something load-bearing has cracked, rusted through or been cut where it should not have been, that is a repair worth doing properly rather than plating over. See custom metal fabrication for drawn and repeat work, or rust and weld repairs where corrosion is the real problem.
Planter frames, bench bases, fire pits, trailer racks, security screens, letterbox frames and shade frames. If you can sketch it on the back of an envelope, it can usually be built.
Most repairs are faster and less disruptive done where the metal already is. Pulling a driveway gate off its hinges, getting it onto a ute, taking it away and bringing it back adds two trips and a refit to a job that is often a single weld. That is the case for mobile welding, and it is how the majority of our repair work gets done.
The workshop earns its keep on anything that needs accuracy: a balustrade run that has to be square, a gate frame that has to stay true while it is tacked, cutting and folding, or a piece with a finish that cannot be sprayed in someone's driveway. Those get measured on site, built on the bench, then fitted in one visit.
Metal choice is half the job on the coast. Process follows the metal: MIG for mild steel and thicker section, TIG for thin-wall stainless and aluminium.
The strongest option for the money and the easiest to modify later. It rusts if it is left bare, so it gets a zinc-rich primer and then powder coat or paint. Hot-dip galvanising to AS/NZS 4680 is the other route, and repairing damaged galvanising afterwards is a real and normal step rather than a sign of a bad job. Inland, a well-coated steel job holds up. Within a few streets of the surf it needs either a better coating or a different metal.
Grade 304 suits inland and sheltered spots. Closer to the ocean, 316 is the grade to specify, because it resists chloride pitting better than 304. What it does not do is stay spotless. Both 304 and 316 can tea-stain near the coast, and surface finish and regular fresh-water rinsing are what actually control staining. A well-finished rail that gets hosed down occasionally will look better in years to come than a 316 rail that never gets touched. Thin-wall stainless is TIG work.
Light, and the sensible choice for a wide gate you want to swing without a fight, or anything that has to be lifted into place. Aluminium does not rust, but it does pit in salt air, and it suffers galvanic attack where it contacts stainless or steel fixings unless the two metals are isolated with nylon washers or sleeves. That detail gets missed, and getting it right is what makes an aluminium job last. It welds differently to steel and needs the right machine and technique, which is why plenty of welders will not quote on it.
Send a photo of the problem or describe it over the phone. The instant estimate tool on this page will give you a starting point before you have spoken to anyone.
For anything being built rather than repaired, we measure on site. Openings are almost never square and almost never the size they are assumed to be.
You get a firm figure in writing, and you get told whether the work happens on site or on the bench, before anything starts.
Welds dressed back, bare metal primed and coated, gate hung and adjusted so it latches properly.
We do not publish rates, because two jobs that look the same in a photo are often not the same job. What sets the figure is what we can see when we look at it: the metal and how much of it, whether it is a repair or a build from scratch, how hard the spot is to get to, the condition of what is already there, the finish it needs, and whether it can be done on site or has to go through the workshop twice.
So the sequence is simple. Photo or site visit, then a firm figure in writing before any work starts. Variations get agreed in writing before the varied work happens, rather than appearing at the end. Use the instant estimate tool on this page for a ballpark in the meantime, or call 0413 147 335 and talk it through.
We are local to the Illawarra, so a job here is a local run rather than a travel job. The same crew that welds your balustrade also builds the deck it sits on, which means one quote and one trade to deal with instead of a builder waiting on a fabricator. Finished jobs are on our work, and the full coverage list is on all our Illawarra and South Coast service areas.
Send a photo, use the instant estimate, or call 0413 147 335. You will get told what the job needs, what it will cost once it has been looked at, and when it can be done. If it is not worth repairing, you will get told that too. Details are on the contact page, and anyone with a machine or trailer down should start at machinery and trailer repairs.
Welding Fabrication
Real jobs from our own crew, filmed on site. See all our work videos.
Designed and fabricated in-house: 20 mm aluminium stringers with RHS aluminium steps, rust-resistant and built to last, with integrated lighting. Stone tiles and glass balustrades follow from other trades.
Welding 600mm round reinforcing cages for concrete footings, one down, a hundred to go.
A container forklift bent, twisted and out of action. One Saturday call, fast response, straight back to work.
Send a photo and a short description. You get a straight answer on what it needs and what it costs before anything starts.
Most jobs get done at your place. Gates, rails, posts and repairs are all mobile work. Only pieces that need bench accuracy or a sprayed finish go through the workshop, and those get measured on site and fitted in one visit.
Yes, all three. Mild steel and thicker section are MIG work, while thin-wall stainless and aluminium are TIG work with different filler and settings. That difference is why some welders only quote on steel.
Usually a repair. A dropped gate is normally a worn hinge, a cracked weld at the hinge plate or a post that has rusted at the base, and all three are fixable. A new gate makes sense when the frame is rusted through in several places or the design was wrong for the opening to begin with.
Near the water, grade 316 is the one to specify, because it resists chloride pitting better than 304. Neither grade stays spotless, though. Both 304 and 316 can tea-stain near the coast, and surface finish plus regular fresh-water rinsing are what actually control it.
A barrier is required where the fall is 1 metre or more. The minimum height is 865mm measured above the nosing line of stairs and above ramps, and 1m above landings, balconies and other floors. No opening may let a 125mm sphere pass through, and where the opening is at the edge of the floor the gap is 40mm. Where the fall exceeds 4m there is also a no-climb rule, with no horizontal or near-horizontal elements between 150mm and 760mm above the floor. AS 1428.1 does not govern domestic stair handrails, so it is not the right reference for a home.
We look at the job first. The metal and how much of it, the access, the finish and the condition of what is already there all change the figure, so you get a firm price in writing before work starts rather than a rate over the phone. The instant estimate tool on this page gives you a ballpark, and 0413 147 335 gets you a person.
In NSW a written contract is required for residential building work when the contract price is over $5,000 including GST. Work worth $5,000 to $20,000 is covered by a small works contract, and work worth more than $20,000 requires a full home building contract along with home building compensation cover and the insurance certificate that goes with it. The maximum deposit that may be requested is 10 per cent, and that cap applies to small and large jobs alike. Variations should be agreed in writing before the varied work happens.
All 24 suburbs across the Illawarra and South Coast, from Helensburgh down to Nowra. The service areas page carries the full list, grouped into the Northern Illawarra, Central Wollongong, Lake Illawarra and Kiama and South Coast areas.
“Finally found someone who actually turned up when he said he would!”
“Cheerful, quick, and didn't try to upsell me on things I didn't need. Rare these days.”
“Turned a weekend-long headache into a one-visit fix. Absolute legend.”